泰安扬帆数控科技有限公司为您提供等相关信息发布和资讯展示,敬请关注!
咨询服务热线:
13345281377

新闻资讯

产品

公司新闻

焊接机器人的检修保养工作

来源:http://www.tayfsk.com/  发布时间:2022-11-22 浏览次数:0

在使用焊接机器人进行工作的时候,技术人员一定要做好防护措施,以免发生危险,所以要做好机器人的检修保养工作,下面山东数控焊接设备厂家为您讲解分析。
When using a welding robot for work, technicians must take protective measures to avoid danger, so they must do a good job in the repair and maintenance of the robot. Now, Shandong CNC welding equipment manufacturer will explain and analyze for you.
1、保证作业区域和设备的整洁度,如果地面上有油、水、工具、工件等的话,可能会给操作人员带来隐患,引发严重事故。
1. Ensure the cleanliness of the operation area and equipment. If there is oil, water, tools, workpieces, etc. on the ground, it may bring hidden dangers to operators and cause serious accidents.
2、当使用完工具之后都要将其放回到机器人动作范围外的原位置保存,避免机器人与遗忘在夹具上的工具发生碰撞,造成损坏。另外各项操作都完成之后,不要忘了还要打扫机器人和夹具。
2. When the tool is used, it should be put back to its original position outside the robot's motion range to avoid collision between the robot and the tool forgotten on the fixture, causing damage. After all other operations are completed, don't forget to clean the robot and fixture.
山东数控焊接设备
3、对于负责机器人系统集成的人员、系统设备的设计、制造人员一定要理解掌握护栏以及设备的相关知识,有必要通读手册了解出现紧急情况时需采取的正确操作和措施。
3. Personnel responsible for robot system integration, system equipment design and manufacturing personnel must understand and master the relevant knowledge of guardrails and equipment, and it is necessary to read through the manual to understand the correct operation and measures to be taken in case of emergency.
4、工作人员,在作业之前要穿着特定的工作服,佩戴防护措施,起到充分的保护作用。还要严格遵守规则,避免出现意外的事故或伤害,负责机器人维护和检查的人员一定要检查和确认所有与紧急停止相关的电路,并使其按照对应的标准进行。在维护或检查时,要确保随时可按下紧急停止开关,以便需要时立即停止机器人的使用。
4. Workers shall wear specific work clothes and protective measures before operation to fully protect themselves. It is also necessary to strictly abide by the rules to avoid accidents or injuries. The person responsible for robot maintenance and inspection must check and confirm all circuits related to emergency stop and make them comply with the corresponding standards. During maintenance or inspection, make sure that the emergency stop switch can be pressed at any time, so that the robot can be stopped immediately when necessary.
以上就是使用焊接机器人的相关防护措施的相关注意事项,希望大家在使用中可以参考以上几点进行使用,以免发生危险。更多相关内容的了解就来我们网站http://www.tayfsk.com咨询吧!
The above are the precautions related to the protective measures for using welding robots. I hope you can refer to the above points for use in order to avoid danger. For more information, please come to our website http://www.tayfsk.com Consult!

上一篇:焊接专机设备故障的维修方式
下一篇:自动焊接专机的分类以及使用注意