泰安扬帆数控科技有限公司为您提供等相关信息发布和资讯展示,敬请关注!
咨询服务热线:
13345281377

新闻资讯

产品

行业新闻

技术人员使用数控焊接设备如何保障?

来源:http://www.tayfsk.com/  发布时间:2023-06-06 浏览次数:0

数控焊接设备在工业中有很广泛的应用,作为操作人员,在设备出现问题后,是否现知道该如何处理呢?技术人员使用山东数控焊接设备如何保障?下面就来讲讲:
CNC welding equipment is widely used in industry. As operators, do you now know how to handle equipment problems? How can technical personnel ensure safety when using Shandong CNC welding equipment? Let's talk about it now:
1.操作机器的人员一定要熟悉设备的结构以及工作原理和操作方法。
1. Personnel operating the machine must be familiar with the structure, working principles, and operating methods of the equipment.
2.机器操作人员不能戴手套进行操作,女工长发应盘起,不许穿太过宽松的衣服,不准接触皮带,传动部分,刀片等,防止伤人。
2. Machine operators are not allowed to wear gloves for operation. Female workers should curl up their long hair, wear too loose clothes, and do not touch belts, transmission parts, blades, etc. to prevent injury.
3.机器开机前,应检查送纸台面有无放置工具或其它杂物,每次开机时一定要先按电铃,有了本机别的操作员工响应后,方可开机。如果按完电铃后不开车,过一段时间再开车要再按电铃,确认没有问题后再进行运转。启动机器不准直接高速运转,需从速度零开始,逐渐通过速度旋钮达到额定工作速度。
Before starting the machine, it is necessary to check if there are any tools or other debris placed on the paper feeding table. Each time the machine is turned on, it is necessary to press the electric bell first. Only after other operators of the machine respond can the machine be turned on. If you do not drive after pressing the bell, and then drive again after a period of time, you need to press the bell again to confirm that there are no problems before running. Starting the machine at high speed is not allowed. It needs to start from zero speed and gradually reach the rated working speed through the speed knob.
山东数控焊接设备
4.开槽部分要按程序操作,开槽刀和分纸刀的刀口都很锋利,易伤手;开槽上刀一定要落在下刀槽里,处于正中位置调好刀后一定要锁好紧固螺丝,并要注意把铲纸刀放入铲纸槽里,四刀联动调好后也要记得锁紧螺丝,各部调好锁紧后先用手柄转动开槽部几圈,如无异常现象方可继续操作设备。在高速运转时,稍不留神手就会碰到锋利的刀口上,特别要当心。在生产时,如果违反操作规程也很容易造成伤害事故,所以也要注意。
4. The slotting part should be operated according to the program, and the cutting edges of the slotting knife and the paper separating knife are very sharp, which can easily hurt hands; The upper knife of the slotting must fall into the lower knife slot, and be in the center position. After adjusting the knife, be sure to lock the fastening screws, and pay attention to placing the paper scraper into the paper scraper slot. After adjusting the four knife linkage, remember to lock the screws. After each part is adjusted and locked, use the handle to rotate the slotting part a few turns. If there are no abnormalities, continue operating the equipment. When running at high speed, if you don't leave your hand behind, you will hit the sharp edge of the knife, so be particularly careful. During production, it is also easy to cause injury accidents if operating procedures are violated, so attention should also be paid.
技术人员在使用数控焊接设备时,一定要注意以上几点内容,不要因为一时的粗心引发事故,如果出现了一些常见问题,可以根据实际情况进行维修,自己维修不了,可以找相关的维修人员处理。更多相关事项就来我们网站http://www.tayfsk.com咨询!
Technicians must pay attention to the above points when using CNC welding equipment, and do not cause accidents due to carelessness. If some common problems occur, they can repair them according to the actual situation. If they cannot repair them themselves, they can find relevant maintenance personnel to handle them. For more related matters, come to our website http://www.tayfsk.com consulting service

上一篇:自动焊接设备的构成及特点
下一篇:自动焊接专机与焊接机器人的比较分析