泰安扬帆数控科技有限公司为您提供等相关信息发布和资讯展示,敬请关注!
咨询服务热线:
13345281377

新闻资讯

产品

行业新闻

预防数控焊接设备问题出现的参考意见

来源:http://www.tayfsk.com/  发布时间:2022-12-22 浏览次数:0

如果你在使用山东数控焊接设备中遇到了相关问题,可以参考解决,接下来我们来看看在使用设备时要注意哪些?
If you encounter relevant problems in using Shandong CNC welding equipment, you can refer to and solve them. Next, let's take a look at what you should pay attention to when using the equipment?
1.操作机器的人员一定要熟悉设备的结构以及工作原理和操作方法。
1. Personnel operating the machine must be familiar with the structure, working principle and operation method of the equipment.
2.机器操作人员不能戴手套进行操作,女工长发应盘起,不许穿太过宽松的衣服,不准接触皮带,传动部分,刀片等,防止伤人。
2. The machine operator shall not wear gloves for operation. The long hair of the female worker shall be rolled up. It is not allowed to wear too loose clothes. It is not allowed to touch the belt, transmission part, blade, etc. to prevent injury.
3.机器开机前,应检查送纸台面有无放置工具或其它杂物,每次开机时一定要先按电铃,有了本机别的操作员工响应后,方可开机。如果按完电铃后不开车,过一段时间再开车要再按电铃,确认没有问题后再进行运转。启动机器不准直接高速运转,需从速度零开始,逐渐通过速度旋钮达到额定工作速度。
3. Before starting the machine, check whether there are tools or other sundries on the paper feeding table. Each time you start the machine, you must press the bell first. The machine can only be started after other operators respond. If you do not start the car after pressing the bell, you should press the bell again after a period of time to confirm that there is no problem before starting the car. It is not allowed to start the machine directly at high speed. Start from speed zero and gradually reach the rated working speed through the speed knob.
山东数控焊接设备
4.开槽部分要按程序操作,开槽刀和分纸刀的刀口都很锋利,ji易伤手;开槽上刀一定要落在下刀槽里,处于正中位置调好刀后一定要锁好紧固螺丝,并要注意把铲纸刀放入铲纸槽里,四刀联动调好后也要记得锁紧螺丝,各部调好锁紧后先用手柄转动开槽部几圈,如无异常现象方可继续操作设备。在高速运转时,稍不留神手就会碰到锋利的刀口上,特别要当心。在生产时,如果违反操作规程也很容易造成伤害事故,所以也要注意。
4. The slotting part shall be operated according to the procedure. The cutting edges of the slotting knife and the paper separating knife are very sharp, which is easy to hurt hands; The slotting upper knife must fall into the lower knife slot. When the knife is in the center position and adjusted, the fastening screw must be locked. Pay attention to putting the paper shoveling knife into the paper shoveling slot. Remember to lock the screw after the four knife linkage is adjusted. After each part is adjusted and locked, use the handle to rotate the slotting part for several turns. If there is no abnormal phenomenon, continue to operate the equipment. When running at high speed, you will touch the sharp edge if you don't leave your mind. Be careful. During production, it is also easy to cause injury accidents if operating procedures are violated, so attention should also be paid.
技术人员在使用自动焊接设备时,一定要注意以上几点内容,不要因为一时的粗心引发事故,如果出现了一些常见问题,可以根据实际情况进行维修,自己维修不了,可以找相关的维修人员处理。更多相关内容就来我们网站http://www.tayfsk.com咨询吧!
When using automatic welding equipment, technicians must pay attention to the above points. Don't cause accidents due to carelessness. If there are some common problems, they can repair them according to the actual situation. If they can't repair them themselves, they can find relevant maintenance personnel to deal with them. More relevant content will come to our website http://www.tayfsk.com Consult!

上一篇:怎么选择焊接机器人的工件附件
下一篇:自动焊接设备焊接钢件抗压强度不足的解决