随着各种焊接设备的增加与运用，自动化行业也在快速发展，其中不锈钢焊机焊接设备也是许多商家会选择的一种，那你知道不锈钢自动焊接焊机设备有哪些注意事项吗？下面山东焊接专机厂家为您讲解：

With the increase and application of various welding equipment, the automation industry is also developing rapidly. Among them, stainless steel welding equipment is also a type that many businesses will choose. Do you know what precautions should be taken for stainless steel automatic welding equipment? Below, Shandong welding machine manufacturer will explain to you:

不锈钢自动焊机焊接使用的范围多是特殊的焊接材料，在使用范围上主要以钣金焊接、不锈钢薄板的焊接、模具仪器、精密电子、缺陷修复为主。不锈钢自动焊机焊接设备主要注意事项如下：

The welding range of stainless steel automatic welding machines is mostly special welding materials, mainly including sheet metal welding, stainless steel sheet metal welding, mold instruments, precision electronics, and defect repair. The main precautions for stainless steel automatic welding equipment are as follows:

1、使用横向外特性的电源，直流时使用正极性（焊丝接负极）。

1. Use a power supply with lateral external characteristics, and use positive polarity (welding wire connected to negative electrode) for direct current.

2、一般适合6mm以下薄板的焊，具备焊缝成型美观，焊变形量小的特点。

2. Generally suitable for welding thin plates below 6mm, with the characteristics of beautiful weld formation and small welding deformation.

3、维护气体为氩气，纯度为99.99%。当焊电流为50--50A时，氩气流量为8--0L/min，当电流为50--250A时，氩气流量为2--5L/min。

3. The maintenance gas is argon with a purity of 99.99%. When the welding current is 50-50A, the argon flow rate is 8-0L/min, and when the current is 50-250A, the argon flow rate is 2-5L/min.

4、钨极从气体燃烧室引人注目的长度，以4--5mm为佳，，在角焊等遮挡性差的地方是2--3mm，在开槽深的地方是5--6mm，燃烧室工作的距离一般不多达5mm。

4. The striking length of the tungsten electrode from the gas combustion chamber is 4-5mm, which is preferred. In areas with poor shielding such as fillet welding, it is 2-3mm, and in areas with deep grooves, it is 5-6mm. The distance from the combustion chamber to the working area is generally not more than 5mm.

5、为避免焊气孔之经常出现，焊部位如有铁锈、油污等务必清扫整洁。

5. To avoid frequent occurrence of welding pores, any rust, oil stains, etc. on the welding area must be cleaned and cleaned.

6、焊电弧长度，焊普通钢时，以2--4mm为佳，而焊不锈钢时，以1--3mm为佳，过长则维护效果不好。

6. When welding ordinary steel, 2-4mm is the optimal arc length, while when welding stainless steel, 1-3mm is the optimal arc length. If it is too long, the maintenance effect is not good.

7、接入打底时，为避免底层焊道的背面被水解，背面也必须实体维护。

7. When connecting to the bottom layer, gas maintenance must also be carried out on the back side to avoid hydrolysis of the bottom layer weld bead.

8、为使氩气不错地维护焊熔池，和便于施焊操作者，钨极中心线与焊处工件一般应维持80--85°角,填满焊丝与工件表面夹角应尽可能地小，一般为0°左右。

8. In order to maintain the welding pool well with argon gas and facilitate welding operators, the center line of the tungsten electrode should generally maintain an angle of 80-85 ° with the workpiece at the welding point, and the angle between the filled welding wire and the surface of the workpiece should be as small as possible, usually around 0 °.

9、防风与换气，有风的地方，务请采行挡网的措施，而在室内则应采行必要的换气措施。

9. Wind prevention and ventilation. In windy areas, it is important to adopt measures such as mesh blocking, while indoors, necessary ventilation measures should be taken.

通过以上注意事项的介绍，相信您对不锈钢自动焊机焊接设备有了一定的了解。如果有这方面的问题请点击链接提交需求，我们http://www.tayfsk.com帮你提供解决方案。

Through the introduction of the above precautions, I believe you have a certain understanding of stainless steel automatic welding equipment. If you have any questions in this regard, please click on the link to submit the requirements. We http://www.tayfsk.com Help you provide a solution.