泰安扬帆数控科技有限公司为您提供等相关信息发布和资讯展示,敬请关注!
咨询服务热线:
13345281377

新闻资讯

产品

公司新闻

每次使用自动焊接设备焊接操作前的检查

来源:http://www.tayfsk.com/  发布时间:2022-10-18 浏览次数:0

山东自动焊接设备与其他焊接设备相比具有更高的自动化程度,其所有部件均选自高质量的原始设备,并且操作非常简单方便。那么操作员每次使用自动焊接设备焊接操作前的检查包含什么内容呢?
Compared with other welding equipment, Shandong automatic welding equipment has a higher degree of automation. All its components are selected from high-quality original equipment, and the operation is very simple and convenient. What does the operator check before each welding operation with automatic welding equipment include?
自动焊接设备检查:操作员在每次焊接操作前要检查以下项目:
Safety inspection of automatic welding equipment: the operator shall check the following items before each welding operation:
1.确保焊接机相互良好的接地是可靠的安装。
1. Ensure that the welding machine is reliably grounded.
2.确保焊接机的输入和输出电缆完好无损。
2. Ensure that the input and output cables of the welding machine are intact.
3.安装并固定了焊接机后,人员要定期对其进行检查。
3. After the welding machine is installed and fixed, the personnel shall inspect it regularly.
4.不会有内部间隙等异常情况。检查并确认送丝辊的凹槽和齿型完好无损,并且在磨损或接触不良时应更换辊和接触头块。
4. There will be no abnormal conditions such as internal clearance. Check and confirm that the groove and tooth profile of the wire feeding roller are intact, and replace the roller and contact head block in case of wear or poor contact.
山东自动焊接设备
使用自动焊接设备的注意事项:
Precautions for using automatic welding equipment:
1.焊枪电缆不要压得太紧,弯曲角度也不能太小。送丝软管的半径不应小于150mm,否则内部电缆会损坏,可能导致事故。焊接期间请勿更改电压调试开关。
1. The welding gun cable shall not be pressed too tightly and the bending angle shall not be too small. The radius of wire feeding hose shall not be less than 150mm, otherwise the internal cable will be damaged, which may lead to accidents. Do not change the voltage commissioning switch during welding.
2.在焊接操作过程中,请勿触摸带电部件,例如焊接机的输出接口。
2. During the welding operation, do not touch the live parts, such as the output interface of the welding machine.
3.更改或调试面板旋钮时,请勿过分用力。自动不锈钢管焊接机可能会损坏设备。
3. Do not use excessive force when changing or debugging the panel knob. Automatic stainless steel pipe welding machine may damage the equipment.
4.每次焊接之前,请检查焊接机的连接是否正确以及接地线是否可靠。
4. Before each welding, please check whether the welding machine is connected correctly and whether the grounding wire is reliable.
相信大家阅读完文章之后对这一问题有了新的了解和认识,如果您想了解更多知识,欢迎多多关注我们的网站http://www.tayfsk.com动态。
I believe you will have a new understanding of this issue after reading the article. If you want to know more, please pay more attention to our website http://www.tayfsk.com Dynamic.

上一篇:焊接机器人的日常维护工作
下一篇:焊接专机的机械系统的构成思路